Teardown difficulty:
Easy
Duration:
6 min

Recommended tools

Disassembly of the mobile device Acer Liquid Z200 with each step description and the required set of tools.


Specialist in content creation, distribution and content management.


How to disassemble Acer Liquid Z200, Step 1/1 How to disassemble Acer Liquid Z200, Step 1/2

Step 1. Open the back cover

Using a spudger or a plastic pick, carefully, around the edge, detach the back cover clips, and remove it.

Do not insert the tool deeply or bend it. Otherwise, the housing may be tampered with or damaged.

⚠️ Be careful when opening the cover from the volume and power buttons side. Thin cable and fragile buttons are straightforward to damage.


How to disassemble Acer Liquid Z200, Step 2/1 How to disassemble Acer Liquid Z200, Step 2/2

Step 2. Remove the battery

There is a indentation at the end of the battery on the middle cover.

Hook the battery at this point, lift it up and remove the battery.

ℹ️️️️ The Acer Liquid Z200 model has a battery BAT-311 (1|CP5/43/55) with 1300 mAh capacity (aka rechargeable battery).


How to disassemble Acer Liquid Z200, Step 3/1 How to disassemble Acer Liquid Z200, Step 3/2

Step 3. Unscrew the screws

Using a screwdriver (Phillips 1.5 mm PH000), unscrew 8 screws.


How to disassemble Acer Liquid Z200, Step 4/1 How to disassemble Acer Liquid Z200, Step 4/2

Step 4. Remove the middle frame

Pry around the edges. Disconnect attached clips by moving the opening tool along the edge. Remove the middle cover with the contact pads.


How to disassemble Acer Liquid Z200, Step 5/1 How to disassemble Acer Liquid Z200, Step 5/2

Step 5. Remove the rear camera

Pry up the connector and remove the rear (main) camera.


How to disassemble Acer Liquid Z200, Step 6/1 How to disassemble Acer Liquid Z200, Step 6/2 How to disassemble Acer Liquid Z200, Step 6/3 How to disassemble Acer Liquid Z200, Step 6/4 How to disassemble Acer Liquid Z200, Step 6/5 How to disassemble Acer Liquid Z200, Step 6/6 How to disassemble Acer Liquid Z200, Step 6/7

Step 6. Disconnect the connectors

Pry up the connectors for the display, touchscreen.

Besides, it needs to release side buttons and vibration motor. Be careful! The vibration motor is wired and may be glued a bit.

⚠️ Be careful when removing the cables from the connectors. The cables are pretty thin, and it is easy enough to break them or damage the contact tracks inside.


How to disassemble Acer Liquid Z200, Step 7/1 How to disassemble Acer Liquid Z200, Step 7/2

Step 7. Remove the motherboard

Carefully remove the printed circuit board. There is no need to use a lever or try to reach the board by force. Make sure that nothing is getting in the way or holding the board.

⚠️ Do not bend the circuit board when removing it or push tools under it. Unbeknownst to yourself, you can damage components or cables from the inside.


How to disassemble Acer Liquid Z200, Step 8/1 How to disassemble Acer Liquid Z200, Step 8/2

Step 8. Remove the loudspeaker

Pry at the edges and remove the loudspeaker. The loudspeaker may be glued.


How to disassemble Acer Liquid Z200, Step 9/1 How to disassemble Acer Liquid Z200, Step 9/2 How to disassemble Acer Liquid Z200, Step 9/3

Step 9. In the display frame remained

ℹ️️ In the display frame remained:

Detailed disassembly instructions of Acer Liquid Z200 in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.


Disassembling\Repair has easy complexity and takes about 6 minutes in time. Our manual is suitable for all models Acer Liquid Z200 released for markets in different countries.



Back to the list
˄˅

Advertisement

˃˂

Advertisement