Teardown difficulty:
Moderate
Duration:
20 min

Recommended tools

Disassembly/Repair of the mobile device Oukitel WP8 Pro with each step description and the required set of tools.


Specialist in content creation, distribution and content management.


How to disassemble Oukitel WP8 Pro, Step 1/1

Step 1. Before disassembling!

⚠️ Before disassembling, do not forget to turn your phone off.


How to disassemble Oukitel WP8 Pro, Step 2/1 How to disassemble Oukitel WP8 Pro, Step 2/2 How to disassemble Oukitel WP8 Pro, Step 2/3 How to disassemble Oukitel WP8 Pro, Step 2/4

Step 2. Remove the tray

Use the Key tool (aka Needle) or Paperclip. Push the tip all the way into the hole until the tray ejects, and then pull the tray of SIM and Memory card (Micro SD) out.

⚠️ Pay attention! The tool must be inserted into a hole on the edge of the phone's housing. Do not press too hard. It may break the tray eject mechanism.


How to disassemble Oukitel WP8 Pro, Step 3/1 How to disassemble Oukitel WP8 Pro, Step 3/2 How to disassemble Oukitel WP8 Pro, Step 3/3 How to disassemble Oukitel WP8 Pro, Step 3/4 How to disassemble Oukitel WP8 Pro, Step 3/5

Step 3. Open the display module

We recommend using a special heating device such as a separator machine, heat gun, or heating mat. It will simplify the process. You can use a home hairdryer, but you will have to make a nozzle by hand or have a suitable one in the kit to gently heat and concentrate the heat flow in the right place.

ℹ️️ The surface of the display module must be heated to soften the adhesive underneath. The approximate heating temperature is 50° C / 125° F.

Use a thin plastic film or pick for separation. To facilitate the process, you can use isopropyl alcohol. It is often most difficult to pass the tool between the parts to be divided. Choose the far edge from the FFC cables or buttons.

Do not use a lever or any force for separation that could damage the elements inside.

The process can be seen in our video entirely so as well as in detail, at the end of the instructions.


How to disassemble Oukitel WP8 Pro, Step 4/1 How to disassemble Oukitel WP8 Pro, Step 4/2 How to disassemble Oukitel WP8 Pro, Step 4/3 How to disassemble Oukitel WP8 Pro, Step 4/4

Step 4. Remove the bracket

Using a screwdriver (Phillips 1.5 mm PH000), unscrew one screw and remove the bracket holding the connectors.


How to disassemble Oukitel WP8 Pro, Step 5/1 How to disassemble Oukitel WP8 Pro, Step 5/2 How to disassemble Oukitel WP8 Pro, Step 5/3

Step 5. Disconnect the connector

Pry up the connector and remove the display module.


How to disassemble Oukitel WP8 Pro, Step 6/1 How to disassemble Oukitel WP8 Pro, Step 6/2 How to disassemble Oukitel WP8 Pro, Step 6/3

Step 6. Unscrew the screws

Using a screwdriver (Phillips 1.5 mm PH000), unscrew 12 screws.


How to disassemble Oukitel WP8 Pro, Step 7/1 How to disassemble Oukitel WP8 Pro, Step 7/2 How to disassemble Oukitel WP8 Pro, Step 7/3

Step 7. Open the middle cover

Carefully remove the middle cover.


How to disassemble Oukitel WP8 Pro, Step 8/1 How to disassemble Oukitel WP8 Pro, Step 8/2

Step 8. Disconnect the battery connector

Disconnect the battery connector as soon as possible.

ℹ️️ The Oukitel WP8 Pro model has a battery S79 (1ICP5/66/90) with 5000 mAh capacity (aka rechargeable battery).

⚠️ It is highly recommended to disconnect the connector to avoid possible short circuits during disassembly.

Also, try not to use a metal tool to disconnect the rechargeable battery connector or do it carefully.


How to disassemble Oukitel WP8 Pro, Step 9/1 How to disassemble Oukitel WP8 Pro, Step 9/2 How to disassemble Oukitel WP8 Pro, Step 9/3 How to disassemble Oukitel WP8 Pro, Step 9/4

Step 9. Remove the inter-board cable

Carefully, preferably from the edge, disconnect the connectors and remove the inter-board cable connecting the mainboard to the daughterboard (also known as the sub-board).

⚠️ Be careful when removing the cables from the connectors, the cables are pretty thin, and it is easy enough to break them or damage the contact tracks inside.

ℹ️️ The names on the FFC cable (flexible flat cable) indicate its correct position.


How to disassemble Oukitel WP8 Pro, Step 10/1 How to disassemble Oukitel WP8 Pro, Step 10/2 How to disassemble Oukitel WP8 Pro, Step 10/3

Step 10. Unscrew the screws

Using a screwdriver (Philips 1.5 mm PH000), unscrew the four screws.


How to disassemble Oukitel WP8 Pro, Step 11/1 How to disassemble Oukitel WP8 Pro, Step 11/2 How to disassemble Oukitel WP8 Pro, Step 11/3

Step 11. Disconnect the connectors

Disconnect the coaxial cable connector, cable to the microphone, on the daughterboard.

⚠️ Do not pull on the cable or pry it with a sharp tool, the connectors are pretty weak and break easily, or the cable falls out of the end (lug).


How to disassemble Oukitel WP8 Pro, Step 12/1 How to disassemble Oukitel WP8 Pro, Step 12/2 How to disassemble Oukitel WP8 Pro, Step 12/3

Step 12. Disconnect the connector

Pry up the fingerprint sensor connector.


How to disassemble Oukitel WP8 Pro, Step 13/1 How to disassemble Oukitel WP8 Pro, Step 13/2 How to disassemble Oukitel WP8 Pro, Step 13/3

Step 13. Remove the loudspeaker

Carefully remove the loudspeaker assembly with sub-board.


How to disassemble Oukitel WP8 Pro, Step 14/1 How to disassemble Oukitel WP8 Pro, Step 14/2 How to disassemble Oukitel WP8 Pro, Step 14/3 How to disassemble Oukitel WP8 Pro, Step 14/4 How to disassemble Oukitel WP8 Pro, Step 14/5 How to disassemble Oukitel WP8 Pro, Step 14/6

Step 14. Remove the daughterboard

Using a screwdriver (Philips 1.5 mm PH000), unscrew three screws and separate the sub-board from the loudspeaker assembly.

ℹ️️ The board contains a charging port (Micro USB), vibration motor, spring contacts for the speaker, and an antenna unit.


How to disassemble Oukitel WP8 Pro, Step 15/1 How to disassemble Oukitel WP8 Pro, Step 15/2 How to disassemble Oukitel WP8 Pro, Step 15/3

Step 15. Remove the battery

Carefully remove the battery.

The process can be seen in our video entirely so as well as in detail, at the end of the instructions.


How to disassemble Oukitel WP8 Pro, Step 16/1 How to disassemble Oukitel WP8 Pro, Step 16/2 How to disassemble Oukitel WP8 Pro, Step 16/3 How to disassemble Oukitel WP8 Pro, Step 16/4

Step 16. Turn over the PCB

Carefully turn over the motherboard. As usual, we have a cable connector on the opposite side.


How to disassemble Oukitel WP8 Pro, Step 17/1 How to disassemble Oukitel WP8 Pro, Step 17/2 How to disassemble Oukitel WP8 Pro, Step 17/3 How to disassemble Oukitel WP8 Pro, Step 17/4

Step 17. Remove the motherboard

Pry up the connector and remove the motherboard.


How to disassemble Oukitel WP8 Pro, Step 18/1 How to disassemble Oukitel WP8 Pro, Step 18/2 How to disassemble Oukitel WP8 Pro, Step 18/3 How to disassemble Oukitel WP8 Pro, Step 18/4

Step 18. Remove the cameras

Pry up the connectors and remove one rear and one front cameras.


How to disassemble Oukitel WP8 Pro, Step 19/1 How to disassemble Oukitel WP8 Pro, Step 19/2 How to disassemble Oukitel WP8 Pro, Step 19/3 How to disassemble Oukitel WP8 Pro, Step 19/4

Step 19. Remove the cameras

Pry up the connectors and remove two rear cameras.


How to disassemble Oukitel WP8 Pro, Step 20/1 How to disassemble Oukitel WP8 Pro, Step 20/2

Step 20. Open the cover

Carefully separate the motherboard and cover.


How to disassemble Oukitel WP8 Pro, Step 21/1 How to disassemble Oukitel WP8 Pro, Step 21/2

Step 21. Remove the coaxial cable

Pry up the connector and remove the coaxial cable.

Detailed disassembly instructions of Oukitel WP8 Pro in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.


Disassembling\Repair has medium complexity and takes about 20 minutes in time. Our manual is suitable for all models Oukitel WP8 Pro released for markets in different countries.



Back to the list
˄˅

Advertisement

˃˂

Advertisement