Teardown difficulty:
Hard
Duration:
15 min

Recommended tools

Disassembly/Repair of the mobile device Samsung Galaxy J6 Plus SM-J610 (Samsung SM-J610FN/DS (Europe); SM-J610G (LATAM, Australia, New Zealand); SM-J610G/DS (LATAM, Brazil, Chile, Philippines, Uruguay); SM-J610G/DS 64GB (Taiwan)) with each step description and the required set of tools.


Specialist in content creation, distribution and content management.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 1/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 1/2

Step 1. Remove the trays

Use the ejection tool (aka Needle) or Paperclip. Push the tip all the way into the hole until the tray ejects, and then pull the tray out. Should do it for each of the SIM and Memory card (Micro SD) trays.

⚠ī¸ī¸ Pay attention! The tool must be inserted into a hole on the edge of the phone's housing. Do not press too hard. It may break the tray eject mechanism.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 2/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 2/2

Step 2. Open the display module

⚠ī¸ī¸ Pay attention! Disassembly has a maximum 3rd difficulty because the process begins with the disassembly of the display module. If you have no experience or are not sure of your skills, we strongly recommend that you contact a specialized service center.

It will simplify the process. You can use a home hairdryer, but you will have to make a nozzle by hand or have a suitable one in the kit to gently heat and concentrate the heat flow in the right place.

ℹī¸ī¸ The surface of the display module must be heated to soften the adhesive underneath. The approximate heating temperature is 50° C / 125° F.

Use a thin plastic film or pick for separation. To facilitate the process, you can use isopropyl alcohol. It is often most difficult to pass the tool between the parts to be divided. Choose the far edge from the FFC cables or buttons.

Do not use a lever or any force for separation that could damage the elements inside.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 3/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 3/2

Step 3. Remove the bracket

Pry at the edge and remove the bracket holding the connector.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 4/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 4/2 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 4/3

Step 4. Disconnect the connector

Pry up the connector and remove the display module.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 5/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 5/2

Step 5. Unscrew the screws

Using a screwdriver Phillips 1.5 mm PH #000, unscrew 18 screws.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 6/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 6/2

Step 6. Open the back cover

Using a spudger or a plastic pick, carefully, around the edge, detach the back cover clips, and remove it.

Do not insert the tool deeply or bend it. Otherwise, the housing may be tampered with or damaged.

⚠ī¸ī¸ Be careful when opening the cover from the volume and power buttons side. Thin cable and fragile buttons are straightforward to damage.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 7/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 7/2

Step 7. Unscrew the screws

Using a screwdriver Phillips 1.5 mm PH #000, unscrew two screws securing the motherboard.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 8/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 8/2

Step 8. Remove the front camera

Disconnect the connector on the motherboard, and remove the front (selfie) camera.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 9/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 9/2

Step 9. Remove the motherboard

Carefully remove the printed circuit board. There is no need to use a lever or try to reach the circuit board by force. Make sure that nothing is getting in the way or holding the circuit board.

The motherboard, also, may be attached with attachments like latches or hooks, be careful.

⚠ī¸ī¸ Do not bend the circuit board when removing it or push tools under it. Unbeknownst to yourself, you can damage components or cables from the inside.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 10/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 10/2

Step 10. Remove the cameras

Disconnect connectors on the motherbord, and remove the assembly of the two rear cameras.


How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 11/1 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 11/2 How to disassemble Samsung Galaxy J6 Plus SM-J610, Step 11/3

Step 11. In the display frame remained

ℹī¸ī¸ In the display frame remained: the loudspeaker, earpiece speaker, battery, and vibration motor.

Detailed disassembly instructions of Samsung Galaxy J6 Plus SM-J610 in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.


Disassembling\Repair has hard complexity and takes about 15 minutes in time. Our manual is suitable for all models Samsung Galaxy J6 Plus SM-J610 — Samsung SM-J610FN/DS (Europe); SM-J610G (LATAM, Australia, New Zealand); SM-J610G/DS (LATAM, Brazil, Chile, Philippines, Uruguay); SM-J610G/DS 64GB (Taiwan) released for markets in different countries.



Back to the list
˄˅

Advertisement

˃˂

Advertisement