⚠️ Before disassembling, do not forget to turn your phone off.
Disassembly/Repair of the mobile device Samsung Galaxy M11 SM-M115 with each step description and the required set of tools.
Step 2. Remove the tray
Use the Key tool (aka Needle) or Paperclip. Push the tip all the way into the hole until the tray ejects, and then pull the tray of SIM and Memory card (Micro SD) out.
⚠️ Pay attention! The tool must be inserted into a hole on the edge of the phone's housing. Do not press too hard. It may break the tray eject mechanism.
Step 3. Open the back cover
Using a spudger or a plastic pick, carefully, around the edge, detach the back cover clips, and remove it.
Do not insert the tool deeply or bend it. Otherwise, the housing may be tampered with or damaged.
⚠️ Be careful when opening the cover from the volume and power buttons side. Thin cable and fragile buttons are straightforward to damage.
⚠️ Pay attention to the fingerprint sensor glued to the back cover from the inside. (if there is one and is glued to the cover)
Step 4. Unscrew the screws
Using a screwdriver (Phillips 1.5 mm PH000), unscrew the six screws.
⚠️ Remember, the one screw is under the fingerprint sensor. Bend the fingerprint sensor cable to the opposite side to reach the screw.
Step 6. Remove the fingerprint sensor
Disconnect the connector. After, we can remove the cover and fingerprint sensor.
Step 7. Disconnect the battery connector
Disconnect connectors of the battery, display module cable, inter-board cable.
Disconnect the battery connector as soon as possible.
ℹ️️ The Samsung Galaxy M11 SM-M115 model has a battery HQ-S71 with 5000 mAh capacity (aka rechargeable battery).
⚠️ It is highly recommended to disconnect the connector to avoid possible short circuits during disassembly.
Also, try not to use a metal tool to disconnect the rechargeable battery connector or do it carefully.
Step 10. Disconnect the connectors
Disconnect the coaxial cable connector, cables to the mainboard, on the daughterboard.
⚠️ Do not pull on the cable or pry it with a sharp tool, the connectors are pretty weak and break easily, or the cable falls out of the end (lug).
Step 11. Remove the daughterboard
Remove the sub-board. It is glued to the frame with metalized tape, so to facilitate the process, the board can be heated a bit.
ℹ️️ The board contains a charging port (Micro USB), microphone, spring contacts for the speaker, vibration motor, and an antenna unit.
⚠️ It is not necessary to insert the tool under the board when removing the sub-board. Internal components could be damaged.
Step 12. Remove the coaxial cable
Disconnect the connector and remove the coaxial cable.
⚠️ Be careful when removing the cables from the connectors, the cables are pretty thin, and it is easy enough to break them or damage the contact tracks inside.
Step 14. Unscrew the screws
Using a screwdriver (Phillips 1.5 mm PH000), unscrew two screws.
ℹ️️ Be sure to note the location of the screws before disassembling. When assembling the device, screwing the screw in the wrong place may damage the device or its parts. To avoid damage, the removed screws and individual pieces (as gaskets or brackets) must be laid out in the appropriate order, or the screws and their holes in the phone must be marked with colored markers.
Step 15. Remove the motherboard
Carefully remove the printed circuit board. There is no need to use a lever or try to reach the board by force. Make sure that nothing is getting in the way or holding the board.
⚠️ Do not bend the circuit board when removing it or push tools under it. Unbeknownst to yourself, you can damage components or cables from the inside.
Step 16. Remove the cameras
Disconnect connectors and remove one rear camera and one front (selfie) camera.
Detailed disassembly instructions of Samsung Galaxy M11 SM-M115 in the video, made by our mobile repair & service center:
If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.
Back to the list