Teardown difficulty:
Easy
Duration:
17 min

Recommended tools

Disassembly/Repair of the mobile device Wileyfox Swift 2 with each step description and the required set of tools.


Specialist in content creation, distribution and content management.


How to disassemble Wileyfox Swift 2, Step 1/1 How to disassemble Wileyfox Swift 2, Step 1/2

Step 1. Remove the tray

Use the ejection tool (aka Needle) or Paperclip. Push the tip all the way into the hole until the tray ejects, and then pull the tray of SIM and Memory card (Micro SD) out.

⚠️️ Pay attention! The tool must be inserted into a hole on the edge of the phone's housing. Do not press too hard. It may break the tray eject mechanism.


How to disassemble Wileyfox Swift 2, Step 2/1 How to disassemble Wileyfox Swift 2, Step 2/2

Step 2. Unscrew the screws

Using a screwdriver (T2 hex), unscrew/drive 2 screws out at the end of the phone.


How to disassemble Wileyfox Swift 2, Step 3/1 How to disassemble Wileyfox Swift 2, Step 3/2

Step 3. Open the back cover

Using a spudger or a plastic pick, carefully, around the edge, detach the back cover clips, and remove it.

Do not insert the tool deeply or bend it. Otherwise, the housing may be tampered with or damaged.

⚠️️ Be careful when opening the cover from the volume and power buttons side. Thin cable and fragile buttons are straightforward to damage.


How to disassemble Wileyfox Swift 2, Step 4/1 How to disassemble Wileyfox Swift 2, Step 4/2

Step 4. Disconnect the battery connector

Disconnect the battery connector as soon as possible. It is better to use a non-metal or plastic tool to avoid any damage.

ℹ️️ The Wileyfox Swift 2 model has a battery with 2700 mAh capacity (aka rechargeable battery).

⚠️️ It is highly recommended to disconnect the connector to avoid possible short circuits during disassembly.


How to disassemble Wileyfox Swift 2, Step 5/1 How to disassemble Wileyfox Swift 2, Step 5/2

Step 5. Unscrew the screws

Using a screwdriver (Philips 1.5 mm PH #000), unscrew the four black screws and three silver screws.

The screws are different: ℹ️️ Be sure to note the location of the screws before disassembling. When assembling the device, screwing the screw in the wrong place may damage the device or its parts. To avoid damage, the removed screws and individual pieces (as gaskets or brackets) must be laid out in the appropriate order, or the screws and their holes in the phone must be marked with colored markers.


How to disassemble Wileyfox Swift 2, Step 6/1 How to disassemble Wileyfox Swift 2, Step 6/2

Step 6. Remove the loudspeaker

Pry over the edge and remove the loudspeaker assembly with antenna tracks.


How to disassemble Wileyfox Swift 2, Step 7/1 How to disassemble Wileyfox Swift 2, Step 7/2

Step 7. Disconnect the connectors

Disconnect the coaxial cable connector, inter-board cable connector.

⚠️️ Do not pull on the cable or pry it with a sharp tool, the connectors are pretty weak and break easily, or the cable falls out of the end (lug).


How to disassemble Wileyfox Swift 2, Step 8/1 How to disassemble Wileyfox Swift 2, Step 8/2

Step 8. Remove the daughterboard

Remove the sub-board. It may be glued to the frame or attached with attachments like latches or hooks, so be careful.

ℹ️️ The sub-board contains a charging port (Micro-USB), microphone, spring contacts for the speaker, and an antenna unit.

⚠️️ It is not necessary to insert the tool underneath when removing the sub-board. Internal components could be damaged.


How to disassemble Wileyfox Swift 2, Step 9/1 How to disassemble Wileyfox Swift 2, Step 9/2

Step 9. Remove the rear camera

Disconnect the connector on the motherboard and remove the rear camera.


How to disassemble Wileyfox Swift 2, Step 10/1 How to disassemble Wileyfox Swift 2, Step 10/2

Step 10. Unscrew the screws

Using a screwdriver (Philips 1.5 mm PH #000), unscrew the six screws.


How to disassemble Wileyfox Swift 2, Step 11/1 How to disassemble Wileyfox Swift 2, Step 11/2

Step 11. Disconnect the connectors

Pry up the connectors of the side buttons cable, display module cable, inter-board cable.

⚠️️ Be careful when removing the cables from the connectors, the cables are pretty thin, and it is easy enough to break them or damage the contact tracks inside.


How to disassemble Wileyfox Swift 2, Step 12/1 How to disassemble Wileyfox Swift 2, Step 12/2

Step 12. Remove the motherboard

⚠️️ Be careful! The coaxial cable is connected from the inside of the motherboard.

Carefully remove the printed circuit board. There is no need to use a lever or try to reach the circuit board by force. Make sure that nothing is getting in the way or holding the circuit board.

The motherboard, also, may be attached with attachments like latches or hooks, be careful.

⚠️️ Do not bend the circuit board when removing it or push tools under it. Unbeknownst to yourself, you can damage components or cables from the inside.


How to disassemble Wileyfox Swift 2, Step 13/1 How to disassemble Wileyfox Swift 2, Step 13/2

Step 13. Remove the battery

With extreme care, remove the battery because it is glued from the inside by the manufacturer.

Also, we need to remember or look in advance at the location of the flat cables under the battery, so as not to damage them.


How to disassemble Wileyfox Swift 2, Step 14/1 How to disassemble Wileyfox Swift 2, Step 14/2 How to disassemble Wileyfox Swift 2, Step 14/3

Step 14. In the display frame remained

ℹ️️ In the display frame remained: the earpiece speaker

Detailed disassembly instructions of Wileyfox Swift 2 in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.


Disassembling\Repair has easy complexity and takes about 17 minutes in time. Our manual is suitable for all models Wileyfox Swift 2 released for markets in different countries.



Back to the list
˄˅

Advertisement

˃˂

Advertisement