Teardown difficulty:
Easy
Duration:
9 min

Recommended tools

Disassembly/Repair of the mobile device ZTE Blade L4 (ZTE Blade L4 A460) with each step description and the required set of tools.


Specialist in content creation, distribution and content management.


How to disassemble ZTE Blade L4, Step 1/1 How to disassemble ZTE Blade L4, Step 1/2

Step 1. Open the back cover

Using a spudger or a plastic pick, carefully, around the edge, detach the back cover clips, and remove it.

Do not insert the tool deeply or bend it. Otherwise, the housing may be tampered with or damaged.

⚠ī¸ī¸ Be careful when opening the cover from the volume and power buttons side. Thin cable and fragile buttons are straightforward to damage.


How to disassemble ZTE Blade L4, Step 2/1 How to disassemble ZTE Blade L4, Step 2/2

Step 2. Remove the battery

There is an indentation at the end of the battery on the middle cover. Hook the battery at this point, lift it up and remove the battery.

ℹī¸ī¸ The ZTE Blade L4 model has a battery Li3822T43P3h736044 with 2200 mAh capacity (aka rechargeable battery).


How to disassemble ZTE Blade L4, Step 3/1 How to disassemble ZTE Blade L4, Step 3/2

Step 3. Unscrew the screws

Using a screwdriver (Phillips 1.5 mm PH #000), unscrew 12 screws.


How to disassemble ZTE Blade L4, Step 4/1 How to disassemble ZTE Blade L4, Step 4/2

Step 4. Open the middle cover

Pry over the edges. Move an opening tool along the edge detach the clips and remove the middle cover with a loudspeaker and antenna pads and tracks. The middle cover protects the printed circuit boards (PCB).

Try to lift the cover by the edges and don't push anything too far inside, so as not to accidentally break or short-circuit anything on the circuit board.


How to disassemble ZTE Blade L4, Step 5/1 How to disassemble ZTE Blade L4, Step 5/2

Step 5. Remove the protective film

Carefully peel off the protective layer hiding the inter-board cable.


How to disassemble ZTE Blade L4, Step 6/1 How to disassemble ZTE Blade L4, Step 6/2

Step 6. Unscrew the screws

Using a screwdriver (Philips 1.5 mm PH000), unscrew the two screws securing the motherboard.


How to disassemble ZTE Blade L4, Step 7/1 How to disassemble ZTE Blade L4, Step 7/2 How to disassemble ZTE Blade L4, Step 7/3

Step 7. Disconnect the connectors

Pry up the side buttons cable. Disconnect the connectors of the display cable, touchscreen cable.

⚠ī¸ī¸ Be careful! The inter-board cable connector, and coaxial cable connector are on the inside.

⚠ī¸ī¸ Be careful when removing the cables from the connectors, the cables are pretty thin, and it is easy enough to break them or damage the contact tracks inside.


How to disassemble ZTE Blade L4, Step 8/1 How to disassemble ZTE Blade L4, Step 8/2

Step 8. Remove the motherboard

Carefully remove the printed circuit board. There is no need to use a lever or try to reach the circuit board by force. Make sure that nothing is getting in the way or holding the circuit board.

The motherboard, also, may be attached with attachments like latches or hooks, be careful.

⚠ī¸ī¸ Do not bend the circuit board when removing it or push tools under it. Unbeknownst to yourself, you can damage components or cables from the inside.


How to disassemble ZTE Blade L4, Step 9/1 How to disassemble ZTE Blade L4, Step 9/2

Step 9. Remove the rear camera

Carefully unstick the body of the main camera.


How to disassemble ZTE Blade L4, Step 10/1 How to disassemble ZTE Blade L4, Step 10/2 How to disassemble ZTE Blade L4, Step 10/3

Step 10. Remove the daughterboard

Carefully peel back the inter-board cable and remove the sub-board.

ℹī¸ī¸ The sub-board contains a charging port (Micro-USB), microphone, spring contacts for antennas.


How to disassemble ZTE Blade L4, Step 11/1 How to disassemble ZTE Blade L4, Step 11/2 How to disassemble ZTE Blade L4, Step 11/3

Step 11. In the display frame remained

ℹī¸ī¸ In the display frame remained: the earpiece speaker, coaxial cable.

Detailed disassembly instructions of ZTE Blade L4 in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.


Disassembling\Repair has easy complexity and takes about 9 minutes in time. Our manual is suitable for all models ZTE Blade L4 — ZTE Blade L4 A460 released for markets in different countries.



Back to the list
˄˅

Advertisement

˃˂

Advertisement