Teardown difficulty:
Easy
Duration:
6 min

Recommended tools

Disassembly/Repair of the mobile device ZTE Blade Q Lux 3G (ZTE Blade Q Lux 3G v830) with each step description and the required set of tools.


Specialist in content creation, distribution and content management.


How to disassemble ZTE Blade Q Lux 3G, Step 1/1 How to disassemble ZTE Blade Q Lux 3G, Step 1/2

Step 1. Open the back cover

Using a spudger or a plastic pick, carefully, around the edge, detach the back cover clips, and remove it.

Do not insert the tool deeply or bend it. Otherwise, the housing may be tampered with or damaged.

⚠ī¸ī¸ Be careful when opening the cover from the volume and power buttons side. Thin cable and fragile buttons are straightforward to damage.


How to disassemble ZTE Blade Q Lux 3G, Step 2/1 How to disassemble ZTE Blade Q Lux 3G, Step 2/2

Step 2. Remove the battery

There is an indentation at the end of the battery on the middle cover. Hook the battery at this point, lift it up and remove the battery.


How to disassemble ZTE Blade Q Lux 3G, Step 3/1 How to disassemble ZTE Blade Q Lux 3G, Step 3/2

Step 3. Unscrew the screws

Using a screwdriver (Phillips 1.5 mm PH #000), unscrew the nine screws.


How to disassemble ZTE Blade Q Lux 3G, Step 4/1 How to disassemble ZTE Blade Q Lux 3G, Step 4/2

Step 4. Open the middle cover

Pry over the edges. Move an opening tool along the edge detach the clips and remove the middle cover with antenna pads and tracks. The middle cover protects the printed circuit board (PCB).

Try to lift the cover by the edges and don't push anything too far inside, so as not to accidentally break or short-circuit anything on the circuit board.


How to disassemble ZTE Blade Q Lux 3G, Step 5/1 How to disassemble ZTE Blade Q Lux 3G, Step 5/2 How to disassemble ZTE Blade Q Lux 3G, Step 5/3 How to disassemble ZTE Blade Q Lux 3G, Step 5/4 How to disassemble ZTE Blade Q Lux 3G, Step 5/5 How to disassemble ZTE Blade Q Lux 3G, Step 5/6 How to disassemble ZTE Blade Q Lux 3G, Step 5/7

Step 5. Disconnect the connectors

Disconnect the display and touchscreen connectors.

Also, we unstick the side buttons and pry up the body of the vibration motor.


How to disassemble ZTE Blade Q Lux 3G, Step 6/1 How to disassemble ZTE Blade Q Lux 3G, Step 6/2

Step 6. Remove the motherboard

Carefully remove the printed circuit board. There is no need to use a lever or try to reach the circuit board by force. Make sure that nothing is getting in the way or holding the circuit board.

The motherboard, also, may be attached with attachments like latches or hooks, be careful.

⚠ī¸ī¸ Do not bend the circuit board when removing it or push tools under it. Unbeknownst to yourself, you can damage components or cables from the inside.


How to disassemble ZTE Blade Q Lux 3G, Step 7/1 How to disassemble ZTE Blade Q Lux 3G, Step 7/2 How to disassemble ZTE Blade Q Lux 3G, Step 7/3

Step 7. In the display frame remained

ℹī¸ī¸ In the display frame remained: the earpiece speaker.

Detailed disassembly instructions of ZTE Blade Q Lux 3G in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.


Disassembling\Repair has easy complexity and takes about 6 minutes in time. Our manual is suitable for all models ZTE Blade Q Lux 3G — ZTE Blade Q Lux 3G v830 released for markets in different countries.



Back to the list
˄˅

Advertisement

˃˂

Advertisement