If the touchscreen does not work, okay.
If the sensor stopped working on its own, then perhaps a simple reboot/restart will help. But, unfortunately, it happens because of some glitches, including on my watch. 🙂
Well, in general, if there is no visible damage, then only disassembly and inspection, moisture may have got inside.
I have a galaxy active 2 and one day while In was wiping the watch, the screen became unresponsive to touches. It seems to have random touches now. there was a time shortly after where it began to work fine but it does not seem to work anymore. There is no visible damage to the device...
Hi, we wrote about the touchscreen problem. For the display, we have the same "solution."
If the display stopped working on its own, then perhaps a simple reboot/restart will help. Also, if there is no visible damage, only when someone looks inside, checks for anything, find something like disconnected cable, a short circuit including the moisture, etc.
Hello, please tell me, I drowned active watch 2 in the sea, at first there was an endless reboot, then the screen flickered, and eventually, they died. has not been worked. I took it for repairs, they told me that it was cheaper to buy a new one. Is seawater really that destructive? Does it make sense to carry it to another service or, for example, send it to you? Thanks.
even how destructive, I drowned the watch myself about two weeks ago in Egypt, two days it held up when I was swimming in the sea) until stopped working.
Seawater is the most destructive liquid for electronics, and often, after swimming in the sea, most of the parts cannot be repaired or restored. In your case, the watch is not so expensive to make the not-so-cheap repair, especially after a repair and saltwater, there is no guarantee that it will work for a long time 🙂
Hello, I have Galaxy Watch Active. Own it for one and a half years. All was good, running, swimming. But today, I once again turned on the swimming workout.
As usual, I swam, and the "back" button (upper) stopped working, plus the Samsung Pay mode was constantly turned on. Using the Samsung Wearable, I reset the watch, restored the backup, and connected the watch with the phone, but the "back" button still has not worked. Please give me advice, what should be done?
Should I dry it in some way? Is there a need to remove the back cover for better drying? I see the dial in the background, and after resetting the clock, it gives out the correct time. But when it comes to the option "Press the BACK button to return," I can't do anything further. The button does not respond by pressing. 🤷♂️🤷♂️🤷♂️
Most likely, liquid has got in, although it is stated that they are waterproof, we have quite a few calls that the devices got malfunctioned due to liquid damage.
Water likely got into the gap between the button and the case and closed the button contacts.
If drying does not help, then you will have to disassemble and change the button directly.
Hello! Would you please tell me? This phone does not charge. It started when charging stops at 60 percent, a few days after connecting the cable, charging stops after a minute. The cables and the charging works, the port is intact.
Hello. The fact that the USB charging port is visually intact does not mean anything. Often there is a break in the contacts where the connector solderers to the bottom board. Therefore, the first step is to check these contacts.
I watched your video on the Samsung active 2. I have an issue with mine where some of the sensors just stopped working - heart rate and wakeup gesture. Then they started working again, then stopped. I suspect something's come to lose inside and need to open the back but I'll have to buy a weird screwdriver for that. Is this the correct one on Amazon.ca
Hi, in our videos, we use Y00 2.0 mm I see no significant difference between 1.5 mm and 2.0 mm screwdriver tips size in repair. Usually, it works well for both (I mean for screw drives 1.5 mm / 2.0 mm).
No without a screwdriver you can't open the back cover without damaging it. If you do not have a Samsung screwdriver, you can use a tri-wings screwdriver for the iPhone. With it / if carefully, you can unscrew the screws.
Hello. If on exactly the same watch as yours in the video the display blinks green, and then became dark. I took it apart. Everything is intact. The screws that attach the back cover were rusty. On the display there seems to be a swelling in the corner. What part should I buy? And how to check what broke? Can it be wiped with alcohol or not? How to reassemble it afterwards so that the watch becomes watertight?
Thank you
Hello. If the AMOLED matrix was blinking green, and then completely went out, then the matrix itself is probably damaged. In this case, nothing can be done; the display module needs to be replaced.
Allan Ong
2021-06-03Team Diligence
2021-06-06Insta_Question
2021-11-24YouTube_Question
2021-11-26YouTube_Question
2021-11-28FB_Question
2021-12-14Andrew Adam
2023-05-18Лол
2023-06-20Edna luna
2023-08-30