Disassembly/Repair of the mobile device Huawei Honor 6C (Huawei Honor 6C DIG-L21HN) with each step description and the required set of tools.

8598

Views

—

Share

14

Questions

Vadim Popoff

Vadim Popoff

Content manager / Author / Content specialist

Content specialist with over 10 years of experience in the technology industry.

Unscrew the screws

Step 1.

Unscrew the screws

Using a screwdriver (hex T4), unscrew the 2 bolts on the end of the phone.

Remove the tray

Step 2.

Remove the tray

Using the key tool, open the SIM card tray and remove it.

âš  Warning!

Do not push too hard this may cause damage.

Open the back cover

Step 3.

Open the back cover

Open the back cover.

Remove the bracket

Step 4.

Remove the bracket

Using a screwdriver (Phillips 1.5 mm PH000), unscrew 3 bolts and remove the bracket holds the connectors.

Disconnect the battery connector

Step 5.

Disconnect the battery connector

Disconnect the battery connector.

âš  Warning!

We strongly recommend disconnecting the connector to avoid a possible short circuit during disassembly.

Open the back cover

Step 6.

Open the back cover

Pry up the fingerprint sensor cable connector on the PCB and remove the back cover.

Remove the coaxial cable

Step 7.

Remove the coaxial cable

Disconnect connectors and remove the coaxial cable.

Unscrew the screws

Step 8.

Unscrew the screws

Using a screwdriver (Phillips 1.5 mm PH000), unscrew 4 bolts in the lower part.

Remove the loudspeaker

Step 9.

Remove the loudspeaker

Pry and remove the buzzer (speaker) assembly.

Unscrew one screw

Step 10.

Unscrew one screw

Using a screwdriver (Phillips 1.5 mm PH000), unscrew 1 bolt in the lower PCB.

Remove the sub-board

Step 11.

Remove the sub-board

Disconnect connector of the inter-board cable on the main PCB and remove the lower board with the cable.

Unscrew the screws

Step 12.

Unscrew the screws

Using a screwdriver (Phillips 1.5 mm PH000), unscrew 3 bolts.

Remove the antenna

Step 13.

Remove the antenna

Pry and remove the upper cover with antennas.

Unscrew the screws

Step 14.

Unscrew the screws

Using a screwdriver (Phillips 1.5 mm PH000), unscrew 3 bolts in the PCB.

Disconnect the connectors

Step 15.

Disconnect the connectors

Disconnect connectors on the PCB.

Remove the motherboard

Step 16.

Remove the motherboard

Remove the PCB.

Disconnect the battery connector

Step 17.

Disconnect the battery connector

Disconnect the battery connector.

âš  Warning!

We strongly recommend disconnecting the connector to avoid a possible short circuit during disassembly.

Remove the vibration motor

Step 18.

Remove the vibration motor

Pry & remove the vibration motor.

Remove the earpiece speaker

Step 19.

Remove the earpiece speaker

Pry and remove the earpiece (speaker).

In the display frame remained

Step 20.

In the display frame remained

Parts in the frame of the display module.

Evgenii Kuzmin

Evgenii Kuzmin

Senior maintenance service and repair engineer
Disassembling\Repair has hard complexity and takes about 10 minutes in time. Our manual is suitable for all models Huawei Honor 6C or Huawei Honor 6C DIG-L21HN released for markets in different countries.
#instructions #Huawei #Huawei Honor 6C
Detailed disassembly instructions of Huawei Honor 6C in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.

logo

8598

Views

—

Share

14

Questions

Top instructions

Check our Top Huawei instructions most liked by readers

New instructions

Check our New Huawei brand instructions on vrm24.com