Disassembly/Repair of the mobile device Huawei Y9s (Huawei Y9s STK-L21) with each step description and the required set of tools.

⚠️ Before disassembling, do not forget to turn your phone off.

Use the ejection tool (aka Needle) or Paperclip. Push the tip all the way into the hole until the tray ejects, and then pull the tray of SIM and Memory card (Micro SD) out.

⚠️ Pay attention! The tool must be inserted into a hole on the edge of the phone's housing. Do not press too hard. It may break the tray eject mechanism.

We recommend using a special heating device such as a separator machine, heat gun, or heating mat. It will simplify the process. You can use a home hairdryer, but you will have to make a nozzle by hand or have a suitable one in the kit to gently heat and concentrate the heat flow in the right place.

ℹ️ The surface of the back cover must be heated to soften the adhesive underneath. The approximate heating temperature is 50° C / 125° F.

Use a thin plastic film or pick for separation. To facilitate the process, you can use isopropyl alcohol. It is often most difficult to pass the tool between the parts to be divided. Choose the far edge from the FFC cables or buttons.

Do not use a lever or any force for separation that could damage the elements inside.

Using a screwdriver (Philips 1.5 mm PH000), unscrew 11 screws.

Pry around the edges. Move an opening tool along the edge detaching the clips and remove the cover. The middle cover protects the printed circuit board (PCB).

Try to lift the cover by the edges and don't push anything too far inside, so as not to accidentally break or short-circuit anything on the circuit board.

Disconnect the battery connector as soon as possible. It it better to use a non-metal or plastic tool to avoid any damage.

ℹ️ The Huawei Y9s STK-L21 model has a battery HB446486ECW with 4000 mAh capacity (aka rechargeable battery).

⚠️ It is highly recommended to disconnect the connector to avoid possible short circuits during disassembly.

Also, try not to use a metal tool to disconnect the rechargeable battery connector or do it carefully.

Using a screwdriver (Philips 1.5 mm PH000), unscrew 7 screws.

Pry around the edges. Disconnect attached clips by moving the opening tool along the edge. Remove the cover securing the sub-board.

Pry around the edges, carefully. Remove the loudspeaker.

Disconnect the coaxial cable connector, cable to the mainboard on the daughterboard.

⚠️ Do not pull on the cable or pry it with a sharp tool. The connectors are pretty weak and break easily, or the cable falls out of the end (lug).

Remove the sub-board. It may be glued to the frame with metalized tape, so to facilitate the process, the sub-board can be heated a bit.

ℹ️ The sub-board contains a charging port (Micro-USB), microphone, vibration motor, spring contacts for the speaker, and an antenna unit.

⚠️ It is not necessary to insert the tool underneath when removing the sub-board. Internal components could be damaged.

Using a screwdriver (Phillips 1.5 mm PH000), unscrew one screw and remove the bracket holding the front (selfie) pop-up camera connector.

Pry up the connectors and remove the three rear cameras. The body of the cameras may be glued to the frame with metalized tape.

Pry up the connectors of the power volume buttons cable, fingerprint sensor cable, display module cable, inter-board cable, and coaxial cable.

⚠️ Be careful when removing the cables from the connectors. The cables are pretty thin, and it is easy enough to break them or damage the contact tracks inside.

Carefully remove the printed circuit board. There is no need to use a lever or try to reach the circuit board by force. Make sure that nothing is getting in the way or holding the circuit board.

⚠️ Do not bend the circuit board when removing it or push tools under it. Unbeknownst to yourself, you can damage components or cables from the inside.

ℹ️ In the display frame remained: the earpiece speaker, battery, front (selfie) pop-up camera, vibration motor.