Disassembly/Repair of the mobile device Apple iPhone 6S Plus (iPhone 6S Plus A1634, A1687, A1690, A1699) with each step description and the required set of tools.

10061

Views

—

Share

5

Questions

Vadim Popoff

Content manager / Author / Content specialist

Content specialist with over 10 years of experience in the technology industry.

Step 1.

Remove the tray

Using the key tool, open the SIM card tray and remove it.

⚠ Warning!

Do not push too hard this may cause damage.


Step 2.

Unscrew the screws
Using a screwdriver (Star Shape 0.8mm Pentalobe), unscrew 2 screws at the end of the phone, securing the display module.

Step 3.

Open the display module
Open the display module.

Step 4.

Remove the bracket
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 2 screws and remove the bracket holding the connectors.

Step 5.

Disconnect the battery connector

Disconnect the battery connector.

⚠ Warning!

We strongly recommend disconnecting the connector to avoid a possible short circuit during disassembly.


Step 6.

Remove the bracket
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 5 screws, and remove the bracket holding the connectors.

Step 7.

Open the display module
Pry up the connectors and remove the display module.

Step 8.

Remove the battery
Remove the battery.

Step 9.

Remove the rear camera
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 2 screws, pry up the connector and remove the main camera.

Step 10.

Remove the bracket
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 2 screws and remove the bracket holding the connector of volume & power buttons.

Step 11.

Remove the antenna
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 1 screw, and remove an antenna.

Step 12.

Remove the antenna
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 2 screws and remove an antenna.

Step 13.

Remove the coaxial cable
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 2 screws and remove the assembly with coaxial cable.

Step 14.

Unscrew the screws
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 2 screws.

Step 15.

Disconnect the connectors
Disconnect the connectors on PCB.

Step 16.

Unscrew the screws
Using a screwdriver (Phillips 1.5 mm PH000)and a screwdriver (Phillips iPhone 2,5 mm), unscrew 2 screws on PCB.

Step 17.

Remove the motherboard
Remove the PCB.

Step 18.

Remove the bracket
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 3 screws, and remove the bracket holding the connectors.

Step 19.

Remove the vibration motor
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 2 screws, pry up the connector and remove the TapTic (vibration motor).

Step 20.

Remove the coaxial cable
Peel back the coaxial cable.

Step 21.

Unscrew the screws
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 6 screws.

Step 22.

Remove the loudspeaker
Remove the buzzer (loudspeaker) assembly.

Step 23.

Unscrew the screws
Using a screwdriver (Phillips 1.5 mm PH000), unscrew 5 screws.

Step 24.

Remove the charging port
Remove the cable with a lightning port, headphone jack/socket, and microphones.

Evgenii Kuzmin

Evgenii Kuzmin

Senior maintenance service and repair engineer

Disassembling\Repair has hard complexity and takes about 31 minutes in time. Our manual is suitable for all models Apple iPhone 6S Plus or iPhone 6S Plus A1634, A1687, A1690, A1699 released for markets in different countries.
Detailed disassembly instructions of Apple iPhone 6S Plus in the video, made by our mobile repair & service center:

If you have a question, ask us, and we will try to answer in as much detail as possible. If this article was helpful for you, please rate it.

logo

10061

Views

—

Share

5

Questions